Vintage Wheels: Order Form

Shipping and taxes (CA residents) will be added to the above total and an invoice will be sent to the purchaser.
Shipping time is 4 – 6 weeks from receipt of the order but may be within 1 week if we have inventory of the items you require.

If hub adapters are required please provide the following dimentions:

Please note the following.
Backspacing of our various wheels is listed on our website www.vintagewheelsus.com
Please ensure that the wheels ordered will fit your car.

INSTALL INFO FOR PIN DRIVE KNOCK OFF WHEELS.
When installing the wheels and hub adapters it is essential that a qualified mechanic/mechanical engineer completes the installation and the following is complied with to ensure vehicle safety.

1) Test fit hub adapters and wheels to ensure backspacing etc is correct for your vehicle before having tires mounted, shortening wheel studs etc.

VINTAGE WHEELS WILL NOT ACCEPT RIMS FOR RETURN IF DAMAGE HAS OCCURRED DURING TIRE FITMENT. –use a tire fitting shop that specializes in scratch free installation.

Vintage Wheels will accept returns if for some reason the wheels do not fit, provided the return is pre approved and the goods are in perfect condition and returned in the original or suitable packing.

2) Fitment of Adapters

The adapters supplied by Vintage wheels have a center spigot (pilot hole) sized correctly to fit a wide range of hubs with 2.75 inch spigots.

Our order forms request that the customer measures the hub spigot diameters and if different from the standard measurements the adapters are re sized accordingly., there may be an up charge..

Please also note that some aftermarket hub , rotor and axle components differ dimensionally from OEM equipment.

Do not use adapters which are not correctly sized as described above otherwise they will not index correctly and you may experience wheel balancing problems.

Adapters are spinners are stamped R for right hand thread (tightens clockwise) and L for left hand thread (tightens counter clockwise) the right hand thread is mounted to the left side of the vehicle and visa versa (looking from the rear of the vehicle)

3) Drive pin lugs

These must be installed using low strength thread locker and tightened as follows. The recommended torque setting for a ½ inch x 20 wheel stud is 85 ft lb. 12mm 80 ft lb , 7/16 inch 80 ft lb

Do not exceed these torque settings and ensure that the lugs are tightened evenly and diagonally.

Ensure the length of the wheel stud into the drive pin lug (adapters in place) uses all of the internal thread and also allows full engagement of a 12 mm hex socket to torque the lugs (Shorter than stock studs may have to be used. ) Wheel studs used must be of the correct grade as supplied by the hub/axle/spindle manufacturer or from a reputable aftermarket wheel stud supplier. .

Also ensure that the wheel adapters seat correctly onto the hub flange with no gap (test with 0.001inch feeler gauge).

4) Tri Wing Spinners

Tri wings to be torqued using a lead hammer of around 5lbs in weight and safety wired.

The safety wire must be pulling the spinner in the direction it tightens. Never use a rubber hammer.!!!!

A small amount of anti seize compound should be used on the mating surfaces of the wheel and the tri wing. Security of tri wings must be checked regularly and immediately following the first short test drive.

Adapters , tri wings spinners and wheels from different manufacturers may not interchange and must be checked by a certified engineer for compatibility before installation.

5) Tires used on the wheels must be correct for the width of the rim and the speed rating of those tires is not to be exceeded.

Knock off wheels of this design may not be legal in your state the onus is on the customer to confirm.

Any components supplied by Vintage Wheels Inc including but not limited to wheels , tri wings, hub adaptors, drive pins, must not be modified in any way ,this could compromise the safety of the component.

SPACERS OF ANY KIND MUST NOT BE USED WITH OUR WHEEL/ADAPTER KITS.

Any components supplied by Vintage Wheels Inc including but not limited to wheels, tri wings, hub adapters, drive pins, must not be modified in any way ,this could compromise the safety of the component. Any components supplied by Vintage Wheels will not necessarily interchange with similar products from other manufacturers.
Wheels and adaptor kits are guaranteed by the Manufacturer against defects caused by workmanship or materials for 12 months from date of sale.
Additionally, the Manufacturer, and/or Importer assume no liability for death, injury, or damage to property incurred either directly or indirectly by the use of the wheels, tri wings and adapter kits. By signing this document, the purchaser acknowledges that he/she understands this exclusion of liability and agrees that he/she and his/her heirs and assigns will hold the Manufacturer, and/or Importer harmless against any and all claims arising from deaths, injuries or damage to property caused either directly or indirectly by the use of the wheels, tri wings and adapter kits and other components.

I have read and fully understand the conditions above

Copyright Vintage Wheels inc
Tel:(619) 952 4717; (888) 720 0459 Fax:(858) 720 0459 email: vintagewheel@aol.com
www.VintagewheelsUS.com
Address: 2683 Via de la Valle #G238 Del Mar CA 92014 USA